3D打印混凝土永久模板组合构件研究综述
Research review of composite members with 3D-printed concrete permanent formwork
关键词:
3D打印混凝土;永久模板;组合构件;界面黏结性能;力学性能;研究进展
Key words:
3D-printed concrete; Permanent formwork; Composite member; Interface bonding performance; Mechanical property; Research progress
刊期:
2026年第6期
DOI:
10.19761/j.1000-4637.25110511
文章编号:
基金项目:
国家重点研发计划项目(2023YFB2604400)。
作者:
许俊翔,张 锐*,曹 禹,宋海军
单位:
西南交通大学 土木工程学院,四川 成都 610031
摘要
摘 要:将3D打印构件用作永久模板,是推动3D打印技术与传统建筑领域深度融合的有效路径。该方法不仅能够显著提升结构构件的综合力学性能与施工效率,还为解决混凝土3D打印技术中长期存在的配筋难题提供了切实可行的解决方案,对推动建筑增材制造技术的工程化应用具有重要意义。本文基于国内外关于3D打印混凝土永久模板组合构件的现有研究成果,系统阐述了混凝土3D打印技术的发展历程与应用现状,重点总结了3D打印混凝土永久模板与后浇混凝土之间的界面黏结性能、3D打印混凝土永久模板组合构件的整体力学性能研究进展,深入分析了当前研究中存在的不足与亟待解决的关键问题。研究成果可为3D打印混凝土永久模板组合结构体系的深入研究、技术优化及工程实践应用提供参考。
Abstract: Using 3D-printed members as permanent formwork is an effective path to promote the in-depth integration of 3D printing technology with the traditional construction field. This method can not only significantly improve the comprehensive mechanical properties and construction efficiency of structural members, but also provide a practical solution for the long-standing problem of steel reinforcement in concrete 3D printing technology, which is of great significance for promoting the engineering application of building additive manufacturing technology. Based on the existing research results on composite members with 3D-printed concrete permanent formwork at home and abroad, this paper systematically elaborates on the development history and application status of concrete 3D printing technology, focuses on summarizing the research progress of the interface bonding performance between 3D-printed permanent formwork and cast-in-place concrete, as well as the mechanical properties of composite members with 3D-printed concrete permanent formwork, and deeply analyzes the deficiencies and urgent key problems existing in the current research. The findings can provide a reference for the in-depth research, technical optimization and engineering practical application of the 3D-printed concrete permanent formwork composite structure system.
结论
(1)3D打印混凝土采用逐层堆叠的成型方式导致现有混凝土结构设计规范在该类结构中的适用性较为有限,尽管我国目前已有T/CECS 786—2020、《3D打印混凝土免拆模板应用技术规范》(征求意见稿)等系列标准,初步建立起了材料、设计、施工与验收的标准框架,但依然缺乏针对该类结构抗震设计的规范条文。因此,未来还需进一步完善相关设计标准,推动该技术从试验研究迈向工程化、规范化应用。
(2)尽管现有规范已为3D打印混凝土永久模板与后浇混凝土的界面黏结强度提供了标准测试方法,但对界面处机械咬合作用的量化贡献及其与材料、工艺参数的关联机制仍不明确。因此,关于3D打印混凝土永久模板与后浇混凝土的黏结性能及其破坏机理还需深入研究。
(3)3D打印混凝土永久模板在吊装、运输及混凝土浇筑过程中承受施工荷载,其在此阶段的变形、强度及稳定性直接影响成型质量与施工安全。因此,未来可着重对该临时工况下的结构行为开展深入研究。
(4)总体而言,随着建筑增材制造技术的不断发展,3D打印混凝土永久模板凭借其施工高效、免拆、受力可靠、适应性强等优势,有望成为未来模板工程的重要发展方向,并有望广泛应用于住宅与公共建筑结构、装配式结构、异形及曲面建筑构件等工程中,尤其适用于复杂造型构件、快速施工项目,具有良好的工程推广价值与广阔应用前景。
参考文献
[1] Mechtcherine V,Bos F P,Perrot A,et al.Extrusion-based additive manufacturing with cement-based materials-production steps, processes, and their underlying physics: A review[J].Cement and Concrete Research,2020,132:106037.
[2] Khan M S,Sanchez F,Zhou Hongyu.3-D printing of concrete: Beyond horizons[J].Cement and Concrete Research,2020,133:106070.
[3] De Schutter G,Lesage K,Mechtcherine V,et al.Vision of 3D printing with concrete: Technical, economic and environmental potentials[J].Cement and Concrete Research,2018,112:25-36.
[4] Bos F P,Menna C,Pradena M,et al.The realities of additively manufactured concrete structures in practice[J].Cement and Concrete Research,2022,156:106746.
[5] Zhu Binrong,Nematollahi B,Pan Jinlong,et al.3D concrete printing of permanent formwork for concrete column construction[J].Cement and Concrete Composites,2021,121:104039.
[6] Qiu Minghong,Qian Ye,Dai Jianguo.Enhancing the flexural performance of concrete beams with 3D-printed UHP-SHCC permanent formwork via graded fiber volume fraction[J].Composite Structures,2024,341:118211.
[7] Bai Meiyan,Xiao Jianzhuang,Wu Yuching,et al.Experimental and numerical study on the flexural behavior of 3D-printed composite beams with U-shaped ECC formwork[J].Engineering Structures,2024,312:118225.
[8] Guan Jingyuan,Wang Li,Huang Yimiao,et al.3D printed concrete composite slabs fabricated by prestress reinforced permanent formwork: Design, manufacturing, and performance[J].Engineering Structures,2025,325:119446.
[9] Wang Hailong,Shen Junyi,Sun Xiaoyan,et al.Numerical investigation on shear behaviour of reinforced concrete beam with 3D printed concrete permanent formwork[J].Journal of Building Engineering,2025,100:111706.
[10] Liu Zhenbang,Li Mingyang,Wang Xiangyu,et al.Axial performances of the steel rebar reinforced column confined by the steel cable reinforced 3D concrete printing permanent formwork[J].Virtual and Physical Prototyping,2024,19(1):e2382163.
[11] William E U.Eskimo house building form: US1995692[P].1935-03-26.
[12] William E U.Molding and depositing machine for solidifiable plastic materials: US2314468[P].1943-03-23.
[13] William E U.Machine for building walls: US2339892[P].1944-01-25.
[14] Pegna J.Exploratory investigation of solid freeform construction[J].Automation in Construction,1997,5(5):427-437.
[15] Khoshnevis B,Bukkapatnam S,Kwon H,et al.Experimental investigation of contour crafting using ceramics materials[J]. Rapid Prototyping Journal,2001,7(1):32-42.
[16] Cesaretti G,Dini E,De Kestelier X,et al.Building components for an outpost on the lunar soil by means of a novel 3D printing technology[J].Acta Astronautica,2014,93:430-450.
[17] Lim S,Buswell R A,Le T T,et al.Developments in construction-scale additive manufacturing processes[J].Automation in Construction,2012,21:262-268.
[18] Le T T,Austin S A,Lim S,et al.Hardened properties of high-performance printing concrete[J].Cement and Concrete Research,2012,42(3):558-566.
[19] 张学辉,郑书玉,陈雄姿,等.打印路径对3D打印混凝土构件力学性能的影响[J].混凝土与水泥制品,2024(7):14-19,28.
[20] Le T T,Austin S A,Lim S,et al.Mix design and fresh properties for high-performance printing concrete[J].Materials and Structures,2012,45(8):1221-1232.
[21] Yang Yekai,Wu Chengqing,Liu Zhongxian,et al.Mechanical anisotropy of ultra-high performance fibre-reinforced concrete for 3D printing[J].Cement and Concrete Composites,2022,125:104310.
[22] 吴凯,赖建中,杜龙雨,等.3D打印超高性能混凝土的抗渗及抗冻性能研究[J].混凝土与水泥制品,2022(10):1-6.
[23] Ma Wei,Wang Guosheng,Zhou Yaya,et al.Polyacrylonitrile fiber reinforced 3D printed concrete: Effects of fiber length and content[J].Journal of Building Engineering,2024,97:110869.
[24] 王海龙,陈杰,高超,等.水泥基材料3D打印技术研究进展[J].中国建材科技,2021,30(3):2-7.
[25] Ding Tao,Xiao Jianzhuang,Zou Shuai,et al.Anisotropic behavior in bending of 3D printed concrete reinforced with fibers[J].Composite Structures,2020,254:112808.
[26] 张超,邓智聪,马蕾,等.3D打印混凝土研究进展及其应用[J].硅酸盐通报,2021,40(6):1769-1795.
[27] 高君峰.3D打印永久性混凝土模板及其叠合构件试验研究[D].杭州:浙江大学,2020.
[28] 葛杰,白洁,杨燕,等.3D打印配筋砌体墙承载力试验研究[J].建筑材料学报,2020,23(2):414-420.
[29] Liu Miao,Zhang Qiyun,Tan Zhendong,et al.Investigation of steel wire mesh reinforcement method for 3D concrete printing[J].Archives of Civil and Mechanical Engineering,2021,21(1):24.
[30] Marchment T,Sanjayan J.Mesh reinforcing method for 3D concrete printing[J].Automation in Construction,2020,109:102992.
[31] Bekaert M,Van Tittelboom K,De Schutter G.3D printed concrete as stay-in-place formwork: Mechanics during casting and curing[J].Structural Concrete,2023,24(1):738-755.
[32] Anton A,Reiter L,Wangler T,et al.A 3D concrete printing prefabrication platform for bespoke columns[J].Automation in Construction,2021,122:103467.
[33] Chen Yidong,Zhang Wenhua,Zhang Yunsheng,et al.3D printed concrete with coarse aggregates: Built in stirrup permanent concrete formwork for reinforced columns[J].Journal of Building Engineering,2023,70:106362.
[34] Wang Li,Yang Yu,Yao Liang,et al.Interfacial bonding properties of 3D printed permanent formwork with the post-casted concrete[J].Cement and Concrete Composites,2022,128:104457.
[35] Qiu Minghong,Sun Yan,Qian Ye.Interfacial bonding performance of 3D-printed ultra-high performance strain-hardening cementitious composites (UHP-SHCC) and cast normal concrete[J].Journal of Building Engineering,2024,82:108268.
[36] Liu Bing,Guo Yazhao,Wang Yang,et al. Study on the compression performance of 3D printing concrete permanent formwork composite columns[J].Journal of Building Engineering, 2024,98:111245.
[37] Guan Jingyuan,Wang Li,Huang Yimiao,et al.Evaluation of the performance of reinforced concrete beams with 3D-printed permanent formwork[J].Journal of Intelligent Construction,2024,2(4):1-17.
[38] Yu Qian,Zuo Qinxin,Zhang Yamei,et al.An investigation on enhancing the bonding properties of 3D printed concrete permanent formwork and post-casted concrete[J].Construction and Building Materials,2024,444:137841.
[39] Chen Yidong,Zhang Yu,Liu Zhiyong,et al.3D-printed concrete permanent formwork: Effect of postcast concrete proportion on interface bonding[J].Materials Letters,2023,344:134472.
[40] Burger J,Huber T,Lloret-Fritschi E,et al.Design and fabrication of optimised ribbed concrete floor slabs using large scale 3D printed formwork[J].Automation in Construction,2022,
144:104599.
[41] Mata-Falcón J,Bischof P,Huber T,et al.Digitally fabricated ribbed concrete floor slabs: A sustainable solution for construction[J].RILEM Technical Letters,2022,7:68-78.
[42] Raza S,Sakha M,Manshadi B,et al.Digital fabrication of ribbed slabs with post-tensioned 3D printed concrete formwork[J].Procedia Structural Integrity,2024,64:1200-1207.
[43] Raza S,Sakha M,Hassan Z,et al.Flexural behavior of stay-in-place load-bearing 3D-printed concrete formwork for ribbed slabs[J].Engineering Structures,2025,338:120531.
[44] Raza S,Manshadi B,Sakha M,et al.Load transfer behavior of 3D printed concrete formwork for ribbed slabs under eccentric axial loads[J].Engineering Structures,2025,322:119148.
[45] 孙晓燕,沈俊逸,王海龙,等.3D打印混凝土永久模板叠合梁抗弯性能研究[J].土木工程学报,2022,55(10):1-10.
[46] 张治成,叶志凯,孙晓燕,等.3D打印混凝土永久模板叠合柱的抗压性能数值模拟研究[J].土木与环境工程学报(中英文),2024,46(1):194-206.
[47] 张洋.水泥基3D打印永久模板制备技术及组合构件力学性能研究[D].南京:东南大学,2020.
[48] Atkinson C D,Aslani F.Performance of 3D printed columns using self-sensing cementitious composites[J].Construction and Building Materials,2023,375:130961.
[49] Guan Jingyuan,Wang Li,Bai Gang,et al.Enhancing 3D printed formwork columns via FRP hoop shear connection reinforcement[J].Structures,2025,79:109545.
[50] Liu Bing,Cheng Xiaoming,Wang Liangang,et al.Compressive performance of PVA fiber-reinforced 3D concrete printing permanent formwork composite columns reinforced with BFRP bars[J].Journal of Building Engineering,2024,98:111174.
[51] Zhang Dan,Ma Guowei,Guan Jingyuan,et al.Cyclic behavior of unbonded post-tensioned precast segmental concrete columns fabricated by 3D printed concrete permanent formwork[J].Engineering Structures,2023,292:116436.
[52] Raza S,Triantafyllidis Z,Anton A,et al.Seismic performance of Fe-SMA prestressed segmental bridge columns with 3D printed permanent concrete formwork[J].Engineering Structures,2024,302:117423.
[53] Tanapornraweekit G,Jiramarootapong P,Paudel S,et al.Experimental and numerical nvestigation of 3D-printed mortar walls under uniform axial compression[J].Construction and Building Materials,2022,360:129552.
[54] Daungwilailuk T,Pheinsusom P,Pansuk W.Uniaxial load testing of large-scale 3D-printed concrete wall and finite-element model analysis[J].Construction and Building Materials, 2021,275:122039.
[55] 耿耀明.3D打印墙体承载力试验研究[J].建筑结构,2021,51(增刊1):1300-1304.
[56] Han Xiaoyu,Yan Jiachuan,Liu Mingjian,et al.Experimental study on large-scale 3D printed concrete walls under axial compression[J].Automation in Construction,2022,133:103993.
[57] 孙浩浩,王一菲,刘化威,等.3D打印混凝土砌体抗剪性能试验与数值模拟研究[J].硅酸盐通报,2025,44(8):2814-2822.
[58] 刘超,王一菲,朱超,等.3D打印混凝土砌体墙抗压性能试验与数值模拟研究[J].西安建筑科技大学学报(自然科学版),2026,58(2):169-177.
[59] Liu Huawei,Wang Yifei,Zhu Chao,et al.Design of 3D printed concrete masonry for wall structures: Mechanical behavior and strength calculation methods under various loads[J].Engineering Structures,2025,325:119374.
[60] 蔡建国,王敬淞,杜彩霞,等.芯柱式3D打印混凝土墙轴心受压性能试验研究[J].建筑结构学报,2024,45(7):31-42.
[61] Wang Jingsong,Zhang Peng,Feng Jian,et al.Experimental study and design approach on 3D printed concrete walls under eccentric axial compression[J].Case Studies in Construction Materials,2024,20:e02892.
[62] Liu Chao,Liang Zhan,Liu Huawei,et al.Seismic performance of 3D printed reinforced concrete walls: Experimental study and numerical simulation[J].Engineering Structures,2025,333:120176.
[63] Zhang Daobo,Feng Peng,Zhou Peizhao,et al.3D printed concrete walls reinforced with flexible FRP textile: Automatic construction, digital rebuilding, and seismic performance[J]. Engineering Structures,2023,291:116488.
[64] Aghajani Delavar M,Chen H,Sideris P.Analysis and design of 3D printed reinforced concrete walls under in-plane quasi-static loading[J].Engineering Structures,2024,303:117535.
引用本文
许俊翔,张锐,曹禹,等.3D打印混凝土永久模板组合构件研究综述[J].混凝土与水泥制品,2026,53(6):1-8. Xu Junxiang,Zhang Rui,Cao Yu,et al.Research review of composite members with 3D-printed concrete permanent formwork[J].China Concrete and Cement Products,2026,53(6):1-8 (in Chinese).
上一个: 不同聚合物乳液对三元胶凝材料体系砂浆黏结强度的影响研究
下一个: 低气压-盐蚀-冻融耦合作用下混凝土盐冻剥蚀数值仿真与试验研究
相关文件