3D打印混凝土层间性能影响因素与测试方法研究综述

头部文案

发布时间：2020-01-06 00:00:00

全国建材科技期刊
全国中文核心期刊
中国科技论文统计源期刊
万方数据-数字化期刊群入网期刊
中国学术期刊（光盘版）全文收录期刊

华东地区优秀科技期刊
江苏省期刊方阵“双效期刊”
中国期刊网全文收录期刊
中国科技期刊数据库全文收录期刊



3D打印混凝土层间性能影响因素与测试方法研究综述

The Review of Research on Influencing Factors and Test Methods of Interlayer Performance of 3D Printed Concrete

2020年第8期

3D打印混凝土；层间强度；配合比；测试方法

3D printed concrete; Interlayer bonding; Mix proportion; Test method

2020年第8期

10.19761/j.1000-4637.2020.08.007.06

国家重点研发计划项目（2018YFC0705800）；国家自然科学基金项目（51908120）；江苏省基础研究计划（自然科学基金）青年项目（SBK2018041259）；中央高校基本科研业务费（2242020K40099）。

於家勉，孙元峰，姚一鸣，鲁聪

东南大学土木工程学院，江苏南京 211189

於家勉，孙元峰，姚一鸣，鲁聪

於家勉,孙元峰,姚一鸣,等.3D打印混凝土层间性能影响因素与测试方法研究综述[J].混凝土与水泥制品,2020(8):7-11,17.

YU J M,SUN Y F,YAO Y M,et al.The Review of Research on Influencing Factors and Test Methods of Interlayer Performance of 3D Printed Concrete China[J].Concrete and Cement Products,2020(8):7-11,17.

浏览量:

1000

摘要：结合国内外研究案例，深入分析了打印工艺、砂浆配合比等3D打印混凝土层间性能的影响因素。在此基础上，进一步探讨了3D打印混凝土层间强度的提高方式。同时总结了抗拉试验、抗剪试验、微观结构分析等层间强度测试方法并分析了各自优缺点。 Abstract: Based on the review of domestic and foreign researches, factors affecting the interlayer bonding of 3D printed concrete were analyzed, such as mix proportion of mortar and printing process. The existing methods of improving the interlayer bonding of 3D printed concrete were summarized. Finally, bonding test methods such as tensile test, shear test and microstructural analysis were compared and summarized.

英文名 : The Review of Research on Influencing Factors and Test Methods of Interlayer Performance of 3D Printed Concrete

刊期 : 2020年第8期

关键词 : 3D打印混凝土；层间强度；配合比；测试方法

Key words : 3D printed concrete; Interlayer bonding; Mix proportion; Test method

刊期 : 2020年第8期

DOI : 10.19761/j.1000-4637.2020.08.007.06

文章编号 :

基金项目 : 国家重点研发计划项目（2018YFC0705800）；国家自然科学基金项目（51908120）；江苏省基础研究计划（自然科学基金）青年项目（SBK2018041259）；中央高校基本科研业务费（2242020K40099）。

作者 : 於家勉，孙元峰，姚一鸣，鲁聪

单位 : 东南大学土木工程学院，江苏南京 211189

於家勉，孙元峰，姚一鸣，鲁聪

於家勉,孙元峰,姚一鸣,等.3D打印混凝土层间性能影响因素与测试方法研究综述[J].混凝土与水泥制品,2020(8):7-11,17.

YU J M,SUN Y F,YAO Y M,et al.The Review of Research on Influencing Factors and Test Methods of Interlayer Performance of 3D Printed Concrete China[J].Concrete and Cement Products,2020(8):7-11,17.





摘要

参数

结论

参考文献

引用本文

摘要：结合国内外研究案例，深入分析了打印工艺、砂浆配合比等3D打印混凝土层间性能的影响因素。在此基础上，进一步探讨了3D打印混凝土层间强度的提高方式。同时总结了抗拉试验、抗剪试验、微观结构分析等层间强度测试方法并分析了各自优缺点。

Abstract: Based on the review of domestic and foreign researches, factors affecting the interlayer bonding of 3D printed concrete were analyzed, such as mix proportion of mortar and printing process. The existing methods of improving the interlayer bonding of 3D printed concrete were summarized. Finally, bonding test methods such as tensile test, shear test and microstructural analysis were compared and summarized.

关键词:

方法

and

the

test

were

打印

bonding

强度

扫二维码用手机看

[1] 马敬畏,蒋正武,苏宇峰.3D打印混凝土技术的发展与展望[J].混凝土世界,2014(7):41-46.

[2] 李福平,邓春林,万晶.3D打印建筑技术与商品混凝土行业展望[J].混凝土世界,2013(3):28-29.
[3] BOS F P,WOLFS R J M,AHMED Z Y,et al.Additive manufacturing of concrete in construction: potentials and challenges of 3D concrete printing[J].Virtual and Physical Prototyping,2016,11(3):209-225.
[4] BUSWELL R A,LEAL W R,JONES S Z,et al.3D printing using concrete extrusion: a roadmap for research[J].Cement and Concrete Research,2018,112:37-49.
[5] 王香港,王申,贾鲁涛,等.3D打印混凝土技术在新冠肺炎防疫方舱中的应用[J].混凝土与水泥制品,2020(4):1-4,13.
[6] 朱彬荣,潘金龙,周震鑫,等.3D打印技术应用于大尺度建筑的研究进展[J].材料导报,2018,32(23):4150-4159.
[7] 王里,王伯林,白刚,等.3D打印混凝土各向异性力学性能研究[J].实验力学,2020,35(2):243-250.
[8] LE T T,AUSTIN S A,LIM S,et al.Hardened properties of high-performance printing concrete[J].Cement and Concrete Research,2012,42(3):558-566.
[9] ZAREIYAN B,KHOSHNEVIS B.Interlayer adhesion and strength of structures in Contour Crafting–effects of aggregate size, extrusion rate, and layer thickness[J].Automation in Construction,2017,81:112-121.
[10] BEUSHAUSEN H,ALEXANDER M G.Bond strength development between concretes of different ages[J].Magazine of Concrete Research,2008,60(1):65-74.
[11] 章苏阳,蒋亚清,王玉,等.3D打印水泥基材料的建造性研究[J].混凝土与水泥制品,2020(5):6-9.
[12] 张云波,张鑫鑫,乔雯钰.可供3D打印的混杂纤维水泥基复合材料及其制备方法:CN201811163971.2[P].2019-02-26.
[13] 肖建庄,马志鸣,段珍华,等.一种用于3D打印的混凝土材料及制备方法:CN201810913908.X[P].2018-12-18.
[14] 马国伟,柴艳龙,王里,等.3D打印陶砂轻质混凝土的制备与力学性能测试[J].实验力学,2020,35(1):58-66.
[15] LEE H,KIM J J,MOON J,et al.Correlation between pore characteristics and tensile bond strength of additive manufactured mortar using X-ray computed tomography[J]. Construction and Building Materials,2019,226:712-720.
[16] LIU G H,LU W B,LOU Y D,et al.Interlayer shear strength of Roller compacted concrete (RCC) with various interlayer treatments[J].Construction and Building Materials,2018,166:647-656.
[17] WOLFS R J M,BOS F P,SALET T A M.Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing[J].Cement and Concrete Research,2018,106:103-116.
[18] PANDA B,PAUL S C,MOHAMED N A N,et al.Measurement of tensile bond strength of 3D printed geopolymer mortar[J].Measurement,2018,113:108-116.
[19] KIM K,PARK S,KIM W,et al.Evaluation of shear strength of RC beams with multiple interfaces formed before initial setting using 3D printing technology[J].Materials,2017,10(12):1-22.
[20] NERELLA V N,HEMPEL S,MECHECHERINE V.Effects of Layer-Interface Properties on Mechanical Performance of Concrete Elements Produced by Extrusion-Based 3D-Printing[J].Construction and Building Materials,2019,205:586-601.
[21] MARCHMENT T,SANJAYAN J G,NEMATOLLAHI B,et al.3D Concrete Printing Technology[M].Oxford:Butterworth-Heinemann,2019.
[22] SAUCIER F,PIGEON M.Durability of new-to-old concrete bonding[J].Symposium Paper,1991(1):689-707.
[23] J?譆LIO E N B S,BRANCO F A,SILVA V D,et al.Influence of added concrete compressive strength on adhesion to an existing concrete substrate[J].Building and Environment,2006,41(12):1934-1939.
[24] CHEN M X,LI L B,ZHENG Y,et al.Rheological and mechanical properties of admixtures modified 3D printing sulphoaluminate cementitious materials[J].Construction and Building Materials,2018,189:601-611.
[25] PANDA B,PAUL S C,TAN M J.Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material[J].Materials Letters,2017,209:146-149.
[26] ARUNOTHAYAN A R,NEMATOLLAHI B,RANADE R,et al.Development of 3D-printable ultra-high performance fiber-reinforced concrete for digital construction[J].Construction and Building Materials,2020,257:119546.
[27] NEMATOLLAHI B,VIJAY P,SANJAYAN J,et al.Effect of polypropylene fibre addition on properties of geopolymers made by 3D printing for digital construction[J].Materials,2018,11(12): 2352.
[28] BONG S H,NEMATOLLAHI B,NAZARI A,et al.Method of optimisation for ambient temperature cured sustainable geopolymers for 3D printing construction applications[J]. Materials,2019,12(6):902.
[29] ZAREIYAN B,KHOSHNEVIS B.Effects of interlocking on interlayer adhesion and strength of structures in 3D printing of concrete[J].Automation in Construction,2017,83:212-221.
[30] MARCHMENT T,SANJAYAN J,XIA M.Method of enhancing interlayer bond strength in construction scale 3D printing with mortar by effective bond area amplification[J]. Materials and Design,2019,169:107684.
[31] WANG L,TIAN Z H,MA G W,et al.Interlayer bonding improvement of 3D printed concrete with polymer modified mortar: Experiments and molecular dynamics studies[J].Cement and Concrete Composites,2020,110:103571.
[32] MA G W,SALMAN N M,WANG L,et al.A novel additive mortar leveraging internal curing for enhancing interlayer bonding of cementitious composite for 3D printing[J].

Construction and Building Materials,2020,244:118305.
[33] HOSSEINI E,ZAKERTABRIZI M,KORAYEM A H,et al.A novel method to enhance the interlayer bonding of 3D printing concrete: An experimental and computational investigation[J].Cement and Concrete Composites,2019,99:112-119.
[34] MECHTCHERIEN V,GRAFE J,NERELLA V N,et al.3D-printed steel reinforcement for digital concrete construction - manufacture, mechanical properties and bond behaviour[J].Construction and Building Materials,2018,179:125-137.
[35] MARCHMENT T,SANJAYAN J.Mesh reinforcing method for 3D Concrete Printing[J].Automation in Construction,2020,109:102992.
[36] DIGGSMCGEE B,KREIGER E,KREIGER M,et al.Print time vs. elapsed time: a temporal analysis of a continuous printing operation for additive constructed concrete[J].Additive Manufacturing,2019,28:205-214.
[37] ASPRONE D,AURICCHIO F,MENNA C,et al.3D printing of reinforced concrete elements: Technology and design approach[J].Construction and Building Materials,2018,165:218-231.
[38] 吴昊一,蒋亚清,潘亭宏,等.3D打印水泥基材料层间结合性能研究[J].新型建筑材料,2019,46(12):5-8.
[39] 刘致远,王振地,王玲,等.3D打印水泥净浆层间拉伸强度及层间剪切强度[J].硅酸盐学报,2019,47(5):648-652.
[40] WOLFS R J,BOS F,SALET T A,et al.Hardened properties of 3D printed concrete: The influence of process parameters on interlayer adhesion[J].Cement and Concrete Research,2019,119:132-140.
[41] RAHUL A V,SANTHANAM M,MEENA H,et al. Mechanical characterization of 3D printable concrete[J].Construction and Building Materials,2019,227:116710.
[42] KLOFT H,KRAUSS H W,HACK N,et al.Influence of process parameters on the interlayer bond strength of concrete elements additive manufactured by Shotcrete 3D Printing (SC3DP)[J].Cement and Concrete Research,2020,134:106078.

上一个

飞机拦阻系统用超轻质混凝土组成设计研究

下一个

我国商品砂浆技术发展现状及展望

头部文案

3D打印混凝土层间性能影响因素与测试方法研究综述

相关文件