高流动性3D打印水泥基材料制备及性能研究_《混凝土与水泥制品》杂志社

头部文案

发布时间：2020-01-06 00:00:00

全国建材科技期刊
全国中文核心期刊
中国科技论文统计源期刊
万方数据-数字化期刊群入网期刊
中国学术期刊（光盘版）全文收录期刊

华东地区优秀科技期刊
江苏省期刊方阵“双效期刊”
中国期刊网全文收录期刊
中国科技期刊数据库全文收录期刊



高流动性3D打印水泥基材料制备及性能研究

Study on Preparation and Properties of High Fluidity 3D Printed Cement-based Materials

2021年第2期

3D打印；胶凝材料；流动性；力学性能；微观分析

3D Printing; Cementitious material; Fluidity; Mechanical property; Microscopic analysis

2021年第2期

10.19761/j.1000-4637.2021.02.008.05

教育部中央科研业务费优秀教师基金项目（2652017164）。

魏玮1，杨涛2

1.内蒙古交通职业技术学院，内蒙古赤峰 024000；2.西南交通大学，四川成都 611756

魏玮1，杨涛2

魏玮,杨涛.高流动性3D打印水泥基材料制备及性能研究[J].混凝土与水泥制品,2021(2):8-12.

WEI W,YANG T.Study on Preparation and Properties of High Fluidity 3D Printed Cement-based Materials[J].CHINA CONCRETE AND CEMENT PRODUCTS,2021(2):8-12.

浏览量:

1000

摘要：为了制备性能良好的3D打印胶凝材料，用碱激发剂对粉煤灰/矿渣胶凝材料进行激发得到了满足可打印性和力学性能的基础材料，并分析了影响胶凝材料性能的最主要因素，基于微观试验结果分析了粉煤灰和碱激发剂对胶凝材料性能的影响机理。结果表明：基础材料的合适掺量和组成为：粉煤灰30%、碱胶比0.56%、碱含量5%、激发剂模数1.0；宜选用CaO含量适中的矿渣，激发剂静置时间应为48 h；影响胶凝材料流动性和力学性能的最主要因素为碱含量；相比于纯矿渣胶凝材料，粉煤灰的掺入使材料表面出现微裂缝，使其强度降低，而碱激发剂的掺入，增强了胶凝材料的密实性，提高了强度。 Abstract: In order to prepare 3D printed cementitious materials with good properties, fly ash/slag cementitious materials were excited by alkali activator, the composition of basic materials satisfying the printability and mechanical properties was obtained, and the main factors affecting the properties of cementitious materials were analyzed. The influence mechanism of fly ash and alkali activator on the properties of cementitious materials was analyzed by microcosmic experiment. The results show that the proper content and composition of the basic materials are as follows: fly ash 30%, ratio of alkali activator soultion to cementitious material 0.56%, alkali content 5%, activator modulus 1.0. The slag with moderate CaO content should be selected and the static time of the activator should be 48 h. The alkali content is the most important factor that affects the fluidity and mechanical properties of cementitious materials. Compared with the pure slag cementitious material, the addition of fly ash causes the micro-cracks on the surface of the material and reduces its strength, while the addition of alkali activator enhances the compactness and strength of the cementitious material.

英文名 : Study on Preparation and Properties of High Fluidity 3D Printed Cement-based Materials

刊期 : 2021年第2期

关键词 : 3D打印；胶凝材料；流动性；力学性能；微观分析

Key words : 3D Printing; Cementitious material; Fluidity; Mechanical property; Microscopic analysis

刊期 : 2021年第2期

DOI : 10.19761/j.1000-4637.2021.02.008.05

文章编号 :

基金项目 : 教育部中央科研业务费优秀教师基金项目（2652017164）。

作者 : 魏玮1，杨涛2

单位 : 1.内蒙古交通职业技术学院，内蒙古赤峰 024000；2.西南交通大学，四川成都 611756

魏玮1，杨涛2

魏玮,杨涛.高流动性3D打印水泥基材料制备及性能研究[J].混凝土与水泥制品,2021(2):8-12.

WEI W,YANG T.Study on Preparation and Properties of High Fluidity 3D Printed Cement-based Materials[J].CHINA CONCRETE AND CEMENT PRODUCTS,2021(2):8-12.





摘要

参数

结论

参考文献

引用本文

Abstract: In order to prepare 3D printed cementitious materials with good properties, fly ash/slag cementitious materials were excited by alkali activator, the composition of basic materials satisfying the printability and mechanical properties was obtained, and the main factors affecting the properties of cementitious materials were analyzed. The influence mechanism of fly ash and alkali activator on the properties of cementitious materials was analyzed by microcosmic experiment. The results show that the proper content and composition of the basic materials are as follows: fly ash 30%, ratio of alkali activator soultion to cementitious material 0.56%, alkali content 5%, activator modulus 1.0. The slag with moderate CaO content should be selected and the static time of the activator should be 48 h. The alkali content is the most important factor that affects the fluidity and mechanical properties of cementitious materials. Compared with the pure slag cementitious material, the addition of fly ash causes the micro-cracks on the surface of the material and reduces its strength, while the addition of alkali activator enhances the compactness and strength of the cementitious material.

扫二维码用手机看

上一个

减缩型聚羧酸系减水剂SRPC-7的合成与性能研究

下一个

饱和泥浆法透水混凝土抗堵性试验研究

头部文案

高流动性3D打印水泥基材料制备及性能研究

相关文件